PM-KUSUM Punjab Application Guide 2026: Subsidy & Process

Punjab grows roughly a quarter of India’s wheat and a fifth of its rice on the back of free agricultural electricity — a policy that costs the state government nearly ₹9,000 crore a year in subsidy paid to PSPCL (Punjab State Power Corporation Limited). For the state’s 12 lakh tubewell-dependent farmers, that free power has hidden costs: rationed daytime supply, single-phase erratic feeders, and night-time pump operation that wastes labour and water. PM-KUSUM (Pradhan Mantri Kisan Urja Suraksha evam Utthaan Mahabhiyan) gives Punjab farmers a way out — daytime solar pumping, owned outright, with the state and central government paying up to 60% of the cost. In 2026, PEDA (Punjab Energy Development Agency) is administering the largest KUSUM rollout the state has seen so far.

This guide walks through the PM-KUSUM Punjab application process for 2026 — Components A, B and C explained for paddy and wheat farmers, the central + state + farmer share for Punjab, the PEDA portal steps, the documents PEDA flags most often in rejections, and how to choose pump HP against your borewell depth and crop pattern.

Direct answer. PM-KUSUM Punjab applications are processed through PEDA (Punjab Energy Development Agency) under three components — A (small grid-connected plants), B (off-grid solar pumps) and C (solarisation of existing grid pumps). The subsidy stack is 30% central (MNRE) + 30% Punjab state + 30% bank loan + 10% farmer contribution. A 5 HP solar pump under Component B costs a Punjab farmer roughly ₹25,000–₹30,000 out of pocket. SC/ST farmers receive an additional state top-up.

If you’re a Punjab farmer with a working tubewell connection — or a barren land parcel near a 33/11 kV substation — KUSUM is the single most subsidised solar scheme available to you in 2026. The challenge is paperwork, not eligibility.

Why Punjab Is a KUSUM Priority State

Punjab sits in a peculiar policy corner. It has India’s most groundwater-intensive agriculture (over 80% irrigation from tubewells), one of the highest agricultural pump densities in the country, and a free-electricity policy that the state government itself describes as financially unsustainable. PM-KUSUM offers the only structural escape — moving farmers off subsidised grid electricity onto self-owned solar generation, without forcing them to give up free water access.

The numbers behind the priority designation come from the Ministry of New and Renewable Energy (MNRE) PM-KUSUM portal and PEDA’s own targets:

• Agricultural pump population: Approximately 14 lakh tubewell connections in Punjab, of which about 12 lakh are active. Per-hectare pump density is the highest in India.
• State subsidy burden: Punjab pays roughly ₹9,000 crore a year to PSPCL as compensation for free agricultural electricity. KUSUM-solarised pumps remove a portion of that burden permanently.
• Solar irradiation: Punjab receives 4.8–5.4 kWh/m²/day across its plains — lower than Rajasthan but more than adequate for high-yield solar pumping during the kharif and rabi pump-heavy windows.
• Crop water demand: Paddy in central Punjab needs 1,800–2,500 mm of water per season versus 400–500 mm for wheat. This creates demand for higher-HP pumps (7.5 HP and 10 HP) in the paddy belt — Sangrur, Patiala, Ludhiana, Moga, Barnala.
• Grid stress: Daytime agricultural feeders in Punjab are routinely overloaded during paddy transplantation (June–July). Solar pumps remove that load directly from the substation.

Punjab’s KUSUM allocation under MNRE’s revised targets through 2026 is among the top five state allocations. PEDA has been clearing applications across all three components — A, B and C — with C (solarisation of existing grid pumps) receiving particular policy attention because it lets the state retain free-power optics while moving generation onto rooftops and farm structures. For background on the national scheme, see our PM KUSUM complete guide 2026.

KUSUM Components in Punjab — A, B, C Explained

PM-KUSUM is a single scheme with three independent components, each addressing a different farmer profile. Punjab implements all three through PEDA, but the application path, vendor list, and subsidy mechanism differ. Picking the wrong component is the most common high-level mistake — and it cannot be corrected later, only re-applied.

Component A — small grid-connected solar plants on barren land. A is for farmers (or co-operatives) with 2–5 acres of barren or fallow land located within 5 km of a 33/11 kV PSPCL substation. The farmer installs a 0.5 MW to 2 MW solar plant (often as a developer-led model on leased land) and PSPCL purchases the generated electricity at a tariff fixed by the Punjab State Electricity Regulatory Commission (PSERC). The farmer earns either a lease rent (developer model) or a power purchase revenue (self-developer model). Component A is best suited to landowners with non-cultivable parcels and capital access.

Component B — stand-alone off-grid solar pumps. B is the highest-volume component for Punjab and the natural fit for farmers without an existing PSPCL connection or in remote areas where the grid is unreliable. The farmer receives a stand-alone solar pump (3, 5, 7.5 or 10 HP) that draws directly from the panels — no grid interface, no metering. Subsidy stack is 30% central + 30% state + 30% bank loan (optional) + 10% farmer share. For deep dives into Component B nationally, see our KUSUM Component B application guide.

Component C — solarisation of existing grid-connected pumps. C lets farmers with an existing PSPCL tubewell connection retain the connection while adding rooftop or pump-shed solar that powers the pump during the day and exports surplus to the grid. Two sub-models exist: individual pump solarisation (IPS) and feeder-level solarisation (FLS). Component C is the most policy-favoured route in Punjab in 2026 because it lets PSPCL claw back free-power subsidy outflow while preserving the farmer’s existing tariff status.

Component	Best for	System type	Subsidy stack	Application route
Component A	Landowners with 2–5 acre barren plot near substation	0.5–2 MW grid-connected plant	Developer model: lease rent. Self-developer: capital + PPA	PEDA tender / EOI route
Component B	Off-grid farmers, no PSPCL connection or remote farms	Stand-alone 3 / 5 / 7.5 / 10 HP solar pump	30% central + 30% state + 30% loan + 10% farmer	PEDA online portal
Component C (IPS)	Farmer with existing PSPCL agri-pump connection	Individual rooftop/ground-mount solar + net-metered pump	30% central + 30% state + 30% loan + 10% farmer	PEDA portal + PSPCL net-metering
Component C (FLS)	Feeder-level solarisation by PSPCL/developer	Substation-level solar feeding multiple pumps	Developer financed; farmer keeps free-power tariff	Tender route via PSPCL

For most Punjab residential farmers reading this guide, Component B and Component C (IPS) are the two relevant tracks. The rest of this article focuses on those.

The 5-Step Punjab KUSUM Application Funnel

This is the framework we use across our PEDA installations — five sequential stages from application to subsidy release. Each stage has its own document set, its own clock, and its own failure modes. Skipping a step or starting one out of order is what turns a 75-day commissioning into a 6-month rework loop.

Step 1: Pre-Application Eligibility Check (Day 0–5)

Before opening the PEDA portal or the central KUSUM portal, confirm five things on paper.

Land ownership match. Your name on the fard jamabandi (Punjab’s land revenue record, equivalent to Rajasthan’s Jamabandi) must match your Aadhaar exactly. Punjab fards often carry full ancestral names — “Gurdeep Singh s/o Kartar Singh” — while Aadhaar may carry “Gurdeep Singh” alone. This single mismatch causes the largest share of PEDA rejections.

Component selection. Confirm whether you want Component B (off-grid pump) or Component C IPS (solarise existing grid pump). If you already have a PSPCL tubewell connection and want to keep daytime free power optics, choose Component C. If you have no PSPCL connection — or a non-functional one in a remote village — choose B.

Borewell depth and pump capacity. Pull out your most recent borewell driller’s certificate or pump replacement bill. PEDA’s pump-HP selection chart is keyed off static water level (SWL) and dynamic water level (DWL). Choosing the wrong HP gets the application rejected at technical review.

Aadhaar–bank seeding. PEDA disburses the state subsidy through Direct Benefit Transfer (DBT). Your bank account must be Aadhaar-seeded — confirm at any bank branch or via UIDAI’s bank-mapper. An unseeded account causes the subsidy bounce-back loop.

Caste certificate (if SC/ST). Punjab provides a state-level top-up for SC and ST farmers under Component B — typically reducing the farmer’s 10% share to 5% or less. Without a current caste certificate, the application defaults to the general subsidy rate.

Step 2: PEDA Portal Registration and Application Submission (Day 6–10)

Open the PEDA portal — or the central kusum.online.gov.in if PEDA’s portal redirects there for the current window. Register with your Aadhaar-linked mobile number. The portal asks for:

1. Component selection (B, C-IPS, or A).
2. Personal details — name, Aadhaar number, mobile, email.
3. Land details — village, tehsil, district, Khasra number, total land area in kanals/acres.
4. Pump details — desired HP, surface or submersible, borewell depth.
5. Bank details — account number, IFSC, branch.
6. Document uploads (see §Punjab KUSUM Documents Checklist below).

Submit the application and screenshot the Application Reference Number (ARN). PEDA then receives the application in its internal queue for verification.

Step 3: Land Verification and Technical Approval (Day 11–35)

PEDA forwards the application to the district Patwari for fard jamabandi verification — typically 10–15 days. Concurrently, PEDA’s technical cell reviews whether the requested pump capacity matches the borewell depth and crop pattern declared. If a 3 HP pump is requested for a 200-foot deep borewell in a paddy district, the technical reviewer flags it as under-specified and either upgrades the recommendation or kicks the file back.

For Component C (IPS), PSPCL also needs to approve the net-metering arrangement on the existing agricultural connection — adding 7–10 days. PSPCL’s renewable energy cell checks the local distribution transformer (DT) loading; over-loaded DTs trigger a conditional clearance with export capping.

Step 4: Farmer Contribution and Vendor Allocation (Day 36–55)

Once technical approval lands, PEDA issues a payment demand for the farmer’s 10% share. Pay via bank transfer or demand draft per PEDA’s instructions — do not pay vendors directly until PEDA confirms allocation. PEDA then assigns an empanelled installer from its current vendor panel.

The empanelled vendor contacts you within 5–7 days for site survey. Installation of a 5 HP off-grid pump takes 3–5 working days end-to-end — borewell connection check, panel structure fabrication, panel mounting, controller wiring, and pump submersion.

Step 5: Commissioning Inspection and Subsidy Release (Day 56–75)

After installation, the vendor uploads commissioning photos and the test report to the PEDA portal. A PEDA inspector visits within 7–14 days. The inspector verifies panel count, inverter/controller model, earthing per IS 3043, water output measurement at full load, and farmer training handover.

On clearance, PEDA releases the 30% state subsidy to the vendor, and triggers MNRE’s central subsidy release (30%) through the PM-KUSUM portal. The vendor’s 5-year AMC obligation begins from the commissioning date.

Punjab KUSUM Documents Checklist

PEDA’s accepted documents set is close to MNRE’s standard list but with Punjab-specific items — the fard jamabandi, the PSPCL agri-connection bill (for Component C), and the caste certificate for state top-ups. All copies must be self-attested unless otherwise specified.

Document	Format / source	Component	PEDA-specific note
Fard jamabandi (land record)	Downloaded from jamabandi.punjab.gov.in or Patwari-issued	B, C, A	Must show applicant as owner / co-owner with Khasra number
Aadhaar card	PDF / image, < 2 MB	B, C, A	Name must match fard jamabandi exactly
PAN card	PDF / image	B, C, A	Required for subsidy DBT compliance
Bank passbook / cancelled cheque	PDF	B, C, A	Aadhaar-seeded account mandatory
Passport photographs	JPG, 2–3 copies	B, C, A	Recent, clear, white background
Borewell depth certificate	Driller’s certificate or groundwater dept record	B, C	Static water level + total depth required
PSPCL agri-bill (last 3 months)	PDF	C only	Account number, sanctioned load, tariff slab
Caste certificate	SC/ST tehsildar-issued	B, C (optional)	Required only for additional state top-up
Self-declaration	PEDA portal-generated PDF	B, C, A	Download, sign, re-upload after Step 2
Land NOC (tenant farmers)	Notarised	B, C	Landowner’s signed NOC plus owner’s fard

For Component A (small plants), additional documents are required: site survey report, soil/topography certificate, and a substation proximity certificate from PSPCL confirming the 33/11 kV connectivity within 5 km. The complete national checklist is detailed in our KUSUM Component B application guide.

Free PEDA document review. Our Punjab team checks your fard jamabandi, Aadhaar match, and borewell certificate before you submit on the PEDA portal — catching the top three causes of rejection. Get your free quote →

Subsidy Math: Central + State + Farmer Share for Punjab

The PM-KUSUM subsidy stack for Punjab is structured around four contributors — the central government (MNRE), the Punjab state government (through PEDA), the bank (optional loan), and the farmer. The default split for general-category farmers under Component B and Component C IPS:

• 30% central subsidy — released by MNRE after commissioning, against PEDA’s commissioning report.
• 30% state subsidy — released by PEDA from the Punjab state budget allocation.
• 30% bank loan — optional, via NABARD-refinanced co-operative banks or rural banks at 4–7% interest.
• 10% farmer contribution — paid upfront after technical approval.

SC/ST farmers receive an additional Punjab state top-up that typically reduces the farmer contribution to 5% or less, with the differential covered from the state’s targeted subsidy programme. This is one of the most generous solar subsidy structures available to any farmer group in India.

Pump Capacity	MNRE benchmark cost	30% central	30% PEDA state	10% farmer share	Optional 30% loan
3 HP surface	₹1,80,000	₹54,000	₹54,000	₹18,000	₹54,000
3 HP submersible	₹2,00,000	₹60,000	₹60,000	₹20,000	₹60,000
5 HP submersible	₹2,85,000	₹85,500	₹85,500	₹28,500	₹85,500
7.5 HP submersible	₹3,80,000	₹1,14,000	₹1,14,000	₹38,000	₹1,14,000
10 HP submersible	₹4,80,000	₹1,44,000	₹1,44,000	₹48,000	₹1,44,000

Note: Benchmark costs are notified annually by MNRE and may be adjusted by PEDA for Punjab-specific tender pricing. The 30% loan is fully optional — farmers with cash flow can simply pay the 10% share and avoid loan interest entirely.

The PEDA process pushes a high share of farmers toward the 10% upfront route because the payback against PSPCL agricultural feeder unreliability and diesel back-up cost is short — typically 6–12 months for off-grid Component B installations. For deeper economics, see the diesel vs solar pump ROI guide.

Common Rejection Reasons in Punjab KUSUM

Across PEDA application cycles we have tracked, rejections cluster around seven patterns. These are all preventable with a 30-minute pre-check before opening the portal.

1. 1
   Name mismatch between fard jamabandi and Aadhaar. Even small differences — "Gurdeep Singh" vs "Gurdeep Singh Sandhu" — get flagged. Apply for fard correction at the Patwari office or Aadhaar correction at the Aadhaar Seva Kendra before submitting.
2. 2
   Pump HP mismatched to borewell depth. Requesting 3 HP for a 220-foot borewell or 10 HP for a 60-foot borewell triggers technical rejection. Match the HP to the static water level table PEDA publishes.
3. 3
   Existing PSPCL agricultural connection (for Component B). Component B is strictly off-grid. If you already have a PSPCL agri-connection, you must apply under Component C IPS instead — or surrender the connection (rarely advisable).
4. 4
   Bank account not Aadhaar-seeded. Subsidy DBT requires Aadhaar–bank seeding. Without it, the state subsidy bounces back to PEDA and the vendor's payment release stalls. Resolve at any bank branch before applying.
5. 5
   Khasra number not in applicant's name. Co-owners must apply jointly or submit a notarised NOC from other co-owners. Inheritance disputes that haven't been resolved in revenue records block the application.
6. 6
   PSPCL bill paid more than 90 days ago (Component C). For Component C IPS, your latest PSPCL agricultural bill must be paid and dated within the last 90 days. An older bill or an unpaid dues balance gets the file rejected at PSPCL net-metering review.
7. 7
   Duplicate Aadhaar across multiple Khasra applications. One farmer Aadhaar may be linked to one approved KUSUM installation in Punjab. Trying to apply for a second pump on a different parcel under the same Aadhaar fails at portal-level deduplication.

PEDA does not auto-close applications immediately — most rejections come with a 30-day window to fix and resubmit. The exception is the borewell-HP mismatch, which requires a fresh technical review and is treated as a new application.

Pump Size Selection: HP, Borewell Depth, Crop Match

Punjab’s crop and groundwater profile means pump sizing differs sharply between the paddy belt (Sangrur, Patiala, Ludhiana, Moga, Barnala, Bathinda) and the wheat-cotton belt (Mansa, Muktsar, Fazilka, parts of Ferozepur). Getting the HP right at application time saves you from technical rejection in Step 3 and from under-performance after commissioning.

Three factors drive correct sizing:

Static water level (SWL) and dynamic water level (DWL). SWL is the depth from ground to the water table in a non-pumping condition; DWL is the depth during active pumping. Punjab’s central and southern belts have SWL of 80–150 feet and DWL pulling down to 120–250 feet during summer paddy transplantation. Higher SWL means the pump needs to lift water over a longer column — more HP.

Crop water requirement per acre per season. Paddy in central Punjab needs 1,800–2,500 mm of water per season (June–October); wheat needs 350–500 mm (November–April); cotton needs 600–800 mm. The pump runs more hours per day during paddy season — sizing must support continuous 8–10 hour operation in summer.

Daily pumping duration target. A KUSUM pump runs on solar — peak output is 5–6 hours per day in Punjab. Choose HP that can move the required daily water volume within those 5–6 hours. Under-sizing means incomplete irrigation rounds.

Pump HP	Best for	Typical borewell depth	Daily output (m³) at 5 hrs sun	Crop suitability
3 HP surface	Open well, shallow borewell, small kitchen-garden plots	Up to 50 ft	35–50 m³	Vegetables, fodder
3 HP submersible	Shallow tubewell, marginal farmers	50–100 ft	30–45 m³	Wheat, mustard on 2–3 acres
5 HP submersible	Mid-depth tubewell, small-medium holdings	80–150 ft	50–75 m³	Wheat, cotton on 4–6 acres
7.5 HP submersible	Deep tubewell, paddy-belt farmers	130–200 ft	80–115 m³	Paddy + wheat rotation, 5–8 acres
10 HP submersible	Very deep tubewell, paddy + sugarcane belts	180–280 ft	110–160 m³	Paddy, sugarcane, 8–12 acres

A farmer in Sangrur with a 180-foot borewell growing paddy on 6 acres should not apply for a 5 HP pump — the 7.5 HP is the correct sizing and PEDA will reclassify it anyway during technical review. A farmer in Mansa with a 90-foot borewell growing cotton-wheat rotation on 5 acres is well-matched to 5 HP. For neighbouring-state comparisons, see KUSUM Rajasthan and KUSUM Gujarat GEDA guide.

Pros and Cons: KUSUM vs Status Quo Free Electricity

Many Punjab farmers ask whether KUSUM is worth the application paperwork when grid electricity is already free. The honest answer depends on your daytime supply reliability and your tolerance for night-time pump operation.

Verdict. For Punjab farmers in the paddy belt with deep borewells (130 ft+), KUSUM Component B or Component C IPS is the better long-term position even against free PSPCL power. The ₹38,000–₹48,000 farmer share on a 7.5–10 HP pump pays back inside one kharif season once you factor diesel back-up savings and the value of daytime irrigation. Farmers with shallow borewells in stable-supply districts may opt to wait, but most will find the math compelling.

How Heaven Green Energy Helps Punjab Farmers

Heaven Green Energy is an MNRE-approved solar EPC company with active operations across Punjab — Ludhiana, Sangrur, Patiala, Bathinda, Mansa, Moga, Barnala, Ferozepur, and Amritsar districts. Our team has supported KUSUM applications through PEDA’s Component B and Component C windows and handles the process end-to-end so farmers don’t lose a planting season to paperwork.

What we do for Punjab farmers:

• Fard jamabandi pre-check — name match against Aadhaar, Khasra verification, co-owner NOCs.
• Borewell-HP correct sizing — driller certificate review, SWL/DWL match, paddy-season buffer recommendation.
• PEDA portal submission — full document upload, ARN tracking, technical query response.
• Component A advisory — for farmers with 2–5 acres of barren land near substations, we model lease-vs-self-developer economics.
• PSPCL net-metering coordination — for Component C IPS, we handle DT loading certificates and meter inspection scheduling.
• Tier-1 ALMM panels + BIS-certified controllers — Adani, Waaree, or Tata panels; no off-list imports that fail inspection.
• 5-year AMC + 25-year performance support — backed by direct O&M contracts.

Explore the services that match your project:

• DREBP & PM-KUSUM services — dedicated KUSUM application support, vendor empanelment, and installation.
• Contact us — free farm assessment and PEDA eligibility check within 24 hours.
• Solar calculator — model your subsidy share and payback in 60 seconds.

For the full national KUSUM picture and component selection guidance, see our PM KUSUM complete guide 2026. For cross-state benchmarks, our KUSUM Rajasthan RRECL guide and KUSUM Gujarat GEDA guide walk through neighbouring-state processes — useful if you farm across the Punjab–Rajasthan or Punjab–Haryana border.

Frequently Asked Questions

How long does the PEDA PM-KUSUM process take from application to commissioning?

The typical end-to-end timeline is 60–90 days from PEDA portal submission to commissioning, with another 15–30 days for the central and state subsidy DBT to settle. Land verification (Step 3) is the longest single step at 15–30 days, depending on Patwari workload in your tehsil. Component C IPS adds 7–10 days for PSPCL net-metering approval. Clean applications with all documents matched at Step 1 typically clear in the lower end of this range.

What is the difference between PM-KUSUM Component B and Component C in Punjab?

Component B is for off-grid farmers — no existing PSPCL agricultural connection — and provides a stand-alone solar pump powered directly by panels. Component C is for farmers with an existing PSPCL agri-connection: C IPS (Individual Pump Solarisation) adds rooftop or ground-mount solar that powers the pump during the day and exports surplus to the grid through PSPCL net-metering. The subsidy stack is identical (30% central + 30% state + 30% loan + 10% farmer) but Component C lets you retain free-power status as back-up.

What is the total subsidy for a Punjab farmer under PM-KUSUM?

Under Component B and Component C IPS, Punjab provides a 60% combined subsidy — 30% central from MNRE and 30% state from PEDA. The farmer pays 10% upfront and can take a 30% NABARD-refinanced bank loan for the remainder, repayable from diesel back-up savings. SC and ST farmers receive an additional state top-up that reduces their share to roughly 5% or lower under targeted Punjab schemes. The subsidy is among the highest available to any farmer group in India.

Can a Punjab farmer with existing PSPCL agricultural connection apply for KUSUM?

Yes — but only under Component C, not Component B. Component B is restricted to off-grid farmers without an active agri-connection. Component C IPS adds solar to your existing pump and lets you keep the free PSPCL connection as back-up. This is the preferred route in Punjab for farmers in the paddy belt who want daytime reliable solar pumping while preserving night-time free-power optics during peak crop windows.

What documents does PEDA require beyond the standard MNRE list?

PEDA accepts MNRE’s standard set plus Punjab-specific items. The Punjab-specific documents are the fard jamabandi (downloaded from jamabandi.punjab.gov.in or Patwari-issued), and for Component C, the latest paid PSPCL agricultural bill within the last 90 days. Caste certificate is required only for SC/ST farmers seeking the additional state top-up. Tenant farmers must submit a notarised NOC from the landowner along with the owner’s fard.

Which Punjab districts have the highest KUSUM application activity?

Sangrur, Patiala, Ludhiana, Bathinda, and Mansa lead Punjab’s KUSUM application volume — these are the paddy-heavy districts with the deepest borewells and the strongest economic case for solar. Moga, Barnala, Ferozepur, and Fazilka follow. Districts in the Doaba and Majha belts (Jalandhar, Hoshiarpur, Amritsar) have lower volumes because grid supply is more reliable there. PEDA allocates slots across all districts — farmers in lower-volume districts often see faster processing.

What happens if PEDA rejects my KUSUM application?

PEDA issues a written rejection on the portal with a specific reason code and typically allows 30 days for resubmission with the flagged issue corrected. The most common fixes are fard jamabandi re-upload after Patwari correction, Aadhaar–bank seeding, and borewell HP reclassification. Complex rejections — usually involving land co-ownership disputes — may need a fresh application. Your ARN stays valid during the 30-day correction window.

Is the KUSUM subsidy available for drip and sprinkler irrigation systems in Punjab?

PM-KUSUM Component B covers the solar pump system itself — panels, controller, pump, and basic delivery pipe. Drip and sprinkler distribution networks are not covered under KUSUM; they are funded through PM Krishi Sinchai Yojana (PMKSY) or Punjab’s state micro-irrigation programmes. The two schemes complement each other — a solar pump under KUSUM combined with drip distribution under PMKSY is the most water-efficient configuration available to a Punjab farmer.

Can I apply for KUSUM Component A for solar plants on barren land in Punjab?

Yes — if you own 2–5 acres of barren or fallow land within 5 km of a 33/11 kV PSPCL substation, you can apply under Component A. The application route is different from B and C — typically a PEDA tender or expression-of-interest process rather than the standard farmer portal. Two operating models exist: developer-led (you lease the land to a solar developer) and self-developer (you install the plant and sell power to PSPCL under a PPA at PSERC-fixed tariff). Heaven Green provides advisory on both models.

How is the central subsidy released for Punjab KUSUM beneficiaries?

The 30% central subsidy is released by MNRE through the PM-KUSUM portal directly to the empanelled vendor’s account after PEDA uploads the commissioning report. The 30% Punjab state subsidy is released by PEDA from the state budget, also to the vendor. The farmer’s 10% share is paid upfront after technical approval (Step 4). The optional 30% bank loan is disbursed to the vendor by NABARD-refinanced banks against the loan agreement signed by the farmer.