Jinko vs Longi Solar Panels India 2027, Detailed Compare

Jinko vs Longi solar panels for India 2027: 7-factor imported panel scorecard, ALMM/DCR status, landed cost, and the few projects where either can be used.

Jinko vs Longi Solar Panels India 2027, Detailed Compare

Jinko Solar and Longi Green Energy are among the world’s largest photovoltaic (PV) module manufacturers; Jinko shipped about 86 GW (gigawatts) of modules in 2025, which it reports as the world’s largest volume for the seventh time. In India, though, the rules around the Ministry of New and Renewable Energy’s (MNRE) Approved List of Models and Manufacturers (ALMM), Basic Customs Duty (BCD) on imported modules, and Domestic Content Requirement (DCR) decide where and when you can actually use them, and since ALMM covers every open-access and net-metering project, that is now a narrow set of private projects.

This guide is written for commercial and utility-scale solar buyers, Engineering, Procurement and Construction (EPC) contractors, independent power producers (IPPs), open-access developers, and SEZ export units, who are evaluating Jinko Tiger Neo against Longi Hi-MO 7 or Hi-MO X6 for projects in India. We cover the technology, the warranty fine print, how the ₹/W (rupees per watt) landed cost builds up, and the specific ALMM / DCR scenarios in which either brand can be used at all.

Direct answer. Jinko Tiger Neo (580 to 605 Wp, 22.45 to 23.42% efficiency on the 72-cell datasheet) is an N-type Tunnel Oxide Passivated Contact (TOPCon) module; Longi Hi-MO 7 (585 to 620 Wp, 21.7 to 23.0%) uses Longi’s N-type HPDC cells, and Hi-MO X6 is its back-contact (HPBC) rooftop line. Neither brand is on ALMM List-I, so neither can be used for PM Suryaghar, government-linked projects, or any net-metering or open-access project; MNRE’s 30 July 2026 O.M. restates that ALMM List-I applies to open-access and net-metering projects. That leaves private captive plants with no net metering or open access, and private mini-grids. On current datasheets Jinko’s 72-cell Tiger Neo has the highest efficiency of the three.

If your project is a behind-the-meter rooftop seeking the ₹78,000 central subsidy, stop reading and pick an Indian ALMM-listed brand, see our Adani vs Waaree comparison or Waaree vs Tata Solar comparison. The same applies to any open-access or net-metered commercial project. For the private projects outside the ALMM order, the Jinko-vs-Longi decision is worth getting right because a 0.3% efficiency gap across 5 megawatts (MW) compounds into lakhs of rupees over 25 years.

Why Jinko and Longi Lead Global PV Module Shipments

Jinko Solar was founded in 2006 in Shangrao, China, and listed on the New York Stock Exchange in 2010. Per jinkosolar.com investor releases, it shipped 86,056 MW of modules in 2025 and reports that it ranked first globally for the seventh time; it is a vertically integrated wafer, cell and module maker. Jinko is widely treated as a Tier-1 supplier.

Longi Green Energy Technology was founded in 2000 in Xi’an, China, and drove the industry’s shift to mono-crystalline silicon, the technology that displaced poly-crystalline panels. Longi (longi.com) is also treated as a Tier-1 supplier and is one of the largest mono-silicon wafer makers, selling wafers to competing module brands.

For an Indian commercial buyer, the practical takeaway is that both manufacturers have the scale to back a long linear performance warranty, though the industry is under strain: Jinko reported 2025 revenue of RMB 65.5 billion (US$9.37 billion), down 29% on 2024, and a net loss for the year. Their scale lets them quote sharp ₹/W numbers and back the warranty with audited financials.

86 GW
Jinko module shipments 2025
Source: JinkoSolar FY2025 results
23.0%
Longi Hi-MO 7 top efficiency
620 Wp, LR7-72HGD datasheet
23.42%
Jinko Tiger Neo top efficiency
605 Wp, JKM580-605N-72HL4-(V) datasheet
40%
Customs duty on imported modules
20% BCD + 20% AIDC, Union Budget 2025-26

The 7-Factor Imported Panel Scorecard

When a procurement head asks us “Jinko or Longi for our 25 MW captive plant?”, we first check whether the project is outside the ALMM order at all, and we never answer on efficiency alone. We use a named framework, The 7-Factor Imported Panel Scorecard: that weighs the seven attributes that actually move the financial model. Use it on every imported-panel RFQ.

Factor 1: Module efficiency (weight: 20%). Higher efficiency means more watts per square metre, lower mounting structure cost, fewer cables, smaller inverter blocks. A 0.3% absolute efficiency gain on a 10 MW (megawatt) project saves roughly 600 square metres of module area (more land once row spacing is counted) and a measurable slice of Balance of System (BoS) cost.

Factor 2: BoS savings (weight: 15%). Higher Wp panels mean fewer module connections, less cabling, fewer mounting feet. A 605 Wp panel vs a 540 Wp panel cuts module count by about 11% for the same DC capacity, that directly drops labour, structure steel, and DC cable costs.

Factor 3: Warranty terms (weight: 15%). Jinko’s Tiger Neo 72-cell and Longi’s Hi-MO 7 datasheets both give a 12-year product warranty and a 30-year linear power warranty; Longi lists a 15-year product and 25-year power warranty for the Hi-MO X6 Explorer. Longer power cover slightly improves levelised cost of energy (LCOE).

Factor 4: ALMM status (weight: 20%). Without ALMM List-I inclusion, the panel cannot be used in government or government-assisted projects, government schemes, or any open-access or net-metering project; from 1 January 2027 those projects also need ALMM List-II cells. Check the latest ALMM amendment at mnre.gov.in before signing a procurement order. For how an ALMM rejection ripples into the bill of quantities, see Heaven Designs’ ALMM list explainer.

Factor 5: BIS / IEC certification (weight: 10%). Any Jinko or Longi panel sold into India must be registered with the Bureau of Indian Standards (BIS) against IS 14286, and both brands’ datasheets cite International Electrotechnical Commission (IEC) 61215 / 61730 certification. Verify the specific model number on the BIS public portal and cross-check the current ALMM amendment on the MNRE ALMM order page before import. For a full walkthrough of what these marks mean, see our BIS, IEC, and ALMM certification guide.

Factor 6: After-sales India footprint (weight: 10%). Warranty claims are only useful if there is a local team to honour them. Jinko lists an Indian subsidiary; for either brand, confirm in writing who handles claims in India. Field-replacement turnaround matters for 20-year-plus assets.

Factor 7: Landed ₹/W (weight: 10%). Quote prices fluctuate weekly because of polysilicon spot pricing, BCD changes, and Renminbi-Rupee FX (foreign exchange). Always compare landed-at-site cost, not factory-gate cost.

Score each factor 1 to 5 and weight to a 100-point total, the brand that crosses 80 wins your RFQ. For the underlying module-selection theory behind this scorecard, see our how to choose solar modules guide.

Jinko Tiger Neo 2027 Lineup

Jinko’s flagship product family in 2026 is Tiger Neo, an N-type TOPCon module series available in 72-cell and 78-cell formats. Current datasheet variants include:

  • Tiger Neo N-type 580 to 605 Wp (JKM580-605N-72HL4-(V)): 22.45 to 23.42% efficiency, 144 half-cut cells (72 × 2), 2,278 × 1,134 mm. Temperature coefficient of −0.29%/°C, first-year degradation 1%, subsequent annual degradation 0.40%, 12-year product and 30-year linear power warranty.
  • Tiger Neo N-type 625 to 650 Wp (JKM625-650N-78HL4-BDV): 22.36 to 23.25% efficiency, 156 half-cut cells (78 × 2), bifacial dual-glass (bifaciality 80 ± 5%), 2,465 × 1,134 mm, utility-scale optimised. Same temperature coefficient.
  • Smaller rooftop formats (54-cell, around 440 Wp) for systems where mechanical handling is constrained.

For panel-technology background, why N-type TOPCon outperforms P-type Mono Passivated Emitter and Rear Cell (PERC), read our Mono PERC vs TOPCon vs Heterojunction (HJT) explainer.

Longi Hi-MO 7 / Hi-MO X6 2027 Lineup

Longi’s two platforms covered here are Hi-MO 7 (N-type HPDC cells, for utility plants) and Hi-MO X6 (Hybrid Passivated Back Contact, or HPBC, for rooftop and distributed projects). The HPBC technology is Longi’s back-contact architecture that moves the electrodes off the front of the cell, capturing more incident light; Longi quotes HPBC cell efficiency above 25.5%.

  • Hi-MO 7 N-type 585 to 620 Wp (LR7-72HGD): 21.7 to 23.0% efficiency, 144 half-cut cells, bifacial dual-glass (bifaciality 80 ± 5%), 2,382 × 1,134 mm. Temperature coefficient −0.28%/°C, first-year degradation under 1%, then 0.4% a year, 12-year product and 30-year power warranty.
  • Hi-MO X6 Explorer (LR5-72HTH, up to 585 Wp): HPBC, 144 cells, 2,278 × 1,134 mm, module efficiency listed at up to 22.5%, 15-year product and 25-year power warranty. Smaller 54-cell versions (LR5-54HTH, LR5-54HTB) suit residential roofs.

HPBC modules typically cost more at the factory gate than equivalent TOPCon, which the financial model has to justify through BoS savings and LCOE improvements.

Get a free imported-panel project review. Our utility-scale and open-access team builds a side-by-side LCOE model for your project using current ₹/W landed quotes. Get your free quote →

Technical Specs Side-by-Side

The table below compares current datasheet SKUs of Jinko Tiger Neo and Longi Hi-MO 7 / Hi-MO X6 for Indian projects outside the ALMM order.

SpecificationJinko Tiger Neo 72HL4-(V)Longi Hi-MO 7 LR7-72HGDLongi Hi-MO X6 LR5-72HTH
Cell technologyN-type TOPConN-type HPDCHPBC (back contact)
Module rated power580 to 605 Wp585 to 620 WpUp to 585 Wp
Module efficiency22.45 to 23.42%21.7 to 23.0%Up to 22.5%
Cell count144 half-cut144 half-cut144
Module dimensions (mm)2,278 × 1,1342,382 × 1,1342,278 × 1,134
Temperature coefficient−0.29%/°C−0.28%/°CCheck datasheet
First-year degradation1.0%Under 1%Check datasheet
Subsequent annual degradation0.40%0.4%Check datasheet
BifacialityBifacial version available80 ± 5% (dual glass)Check datasheet
Operating temperature−40 to +85°C−40 to +85°C−40 to +85°C
BIS / IEC certifiedVerify model on BIS portalVerify model on BIS portalVerify model on BIS portal

Warranty comparison

Warranty terms of the three modules
Warranty termJinko Tiger Neo 72HL4-(V)Longi Hi-MO 7Longi Hi-MO X6 Explorer
Product warranty12 years12 years15 years
Linear performance warranty30 years30 years25 years
Year-1 max degradation1.0%Under 1%Check warranty document
Subsequent annual degradation0.40%0.4%Check warranty document
Guaranteed output at year 3087.4%87.4%Not applicable (25-year term)

How the landed price builds up (imported modules)

How the landed price of an imported module builds up
Cost componentApplies to all three
Factory-gate price (FOB China)Quote-specific; module prices move weekly
Basic Customs Duty (BCD)20% of assessable value
Agriculture Infrastructure and Development Cess (AIDC)20% of assessable value
IGST5% (since 22 September 2025)
Freight, insurance and inland logisticsProject-specific

Customs duty alone adds 40% to the assessable value, so compare quotes only on a landed-at-site basis. There is no reliable public breakdown of how many megawatts of each brand Indian developers have installed, so treat any such deployment figures with caution.

India ALMM and DCR Status, What You Can and Cannot Use

The ALMM is published by MNRE and is the single most important policy gate for any solar panel sold into India. ALMM List-I covers PV modules; List-II covers cells. MNRE’s O.M. of 30 July 2026 restates that only List-I modules may be used in government and government-assisted projects, government schemes, open-access and net-metering projects, and projects selling power to government under section 63 of the Electricity Act. Open-access and net-metering projects commissioned after 31 December 2026 must also use List-II cells. As of MNRE’s updated List-I of 16 September 2026:

  • Jinko Solar: not on ALMM List-I.
  • Longi Green Energy: not on ALMM List-I.

The practical consequences for an Indian buyer:

Where Jinko and Longi modules can and cannot be used in India
Project typeDCR required?ALMM required?Can you use Jinko / Longi?
Residential rooftop PM SuryagharYesYesNo
CFA-subsidised institutional rooftopYesYesNo
Government / PSU procurement (SECI, NTPC tenders)OftenYesNo
Open-access C&I (commercial and industrial)NoYesNo
Net-metered rooftop, even without subsidyNoYesNo
Captive plant with no open access or net meteringNoNoYes
SEZ unit with no open access or net meteringNoNoYes
Mini-grid / micro-grid (private)NoNoYes

For a full breakdown of where DCR rules bite, see our DCR vs non-DCR solar panels explainer.

When Jinko or Longi Make Sense in India

Imported Tier-1 panels are not the right answer for every project. They make economic sense when at least two of the following four conditions hold.

Condition 1: The project is non-DCR and non-ALMM. This is a precondition, not one of two: only private projects with no government involvement, no open access and no net metering qualify, such as captive behind-the-meter plants, SEZ units supplied without open access, and mini-grids built by private operators. In these, you are free to use any BIS-registered, IEC-certified module.

Condition 2: Plant capacity exceeds 5 MW. At sub-5 MW scale the ₹/W advantage of imported panels rarely beats the freight and inventory carrying cost. Above 5 MW, container-load economics kick in and Jinko / Longi factory direct quotes become genuinely competitive, particularly on a ground-mount solar park where layout is optimised around container-lot module counts.

Condition 3: Land-constrained sites where Wp/m² matters. Rooftop and ground-mount sites with hard area constraints, for example, warehouse rooftops capped at 8,000 sqm or land parcels where the developer is paying ₹/sqm rent, benefit from the higher efficiency bins of Tiger Neo or Hi-MO 7.

Condition 4: LCOE-driven private procurement. If your business model is selling power at a fixed tariff from a plant outside the ALMM order, every paise of LCOE matters. The 25-year LCOE difference between a 22.3% module and a 22.8% module is real and worth modelling on large plants.

If none of these conditions hold, choose an Indian ALMM brand, see our Adani vs Tata Solar comparison for the domestic-brand head-to-head, or our products page for solar modules for the full Heaven Green Energy catalogue.

Common Import-Panel Mistakes

Across the imported-panel projects we have audited through 2024 to 25, the same six errors keep surfacing. Each one is preventable with a 30-minute pre-procurement check.

Jinko vs Longi, Verdict by Use Case

Between the two imported brands themselves, and only for projects outside the ALMM order, the scorecard picks by use case:

Use caseBetter choiceWhy
Open-access, net-metering or government-linked projectNeitherALMM List-I modules required
Large captive plant (no open access or net metering)Jinko Tiger Neo 72-cellHighest datasheet efficiency of the three (up to 23.42%)
Land-constrained ground mountJinko Tiger Neo 72-cell or Longi Hi-MO 7Both reach about 23% on current datasheets
Warehouse rooftop without net meteringLongi Hi-MO X6 or Jinko Tiger NeoHi-MO X6 is Longi’s rooftop back-contact line
SEZ unit (no open access or net metering)Either, pick on priceDecide on landed ₹/W
Bifacial tracker plantJinko Tiger Neo 78HL4-BDV or Longi Hi-MO 7Both dual-glass bifacial, about 80% bifaciality
Premium 30-year assetJinko Tiger Neo or Longi Hi-MO 7Both carry 30-year linear power warranties
Jinko Tiger Neo Strengths
  • Highest datasheet efficiency here (up to 23.42% on the 72-cell)
  • 30-year linear power warranty on Tiger Neo
  • Indian subsidiary listed in its filings
  • Strong bifacial product line for tracker plants
Longi Hi-MO Strengths
  • Hi-MO X6 HPBC back-contact cells (above 25.5% cell efficiency, per Longi)
  • 30-year power warranty on Hi-MO 7
  • Hi-MO 7 reaches 23.0% module efficiency
  • Major mono-silicon wafer maker, vertical supply security

Verdict. On the raw numbers, both Jinko Tiger Neo and Longi Hi-MO are technically excellent, and on a large private plant outside the ALMM order an imported SKU can still price sharper than a domestic module. That is the paper case, and the use-case table above ranks the two imported brands against each other. Our recommendation for the projects we execute is the brand we install, stand behind, and warranty-handle locally: as an authorised Channel Partner of Adani Green Energy, Heaven Green Energy installs ALMM-listed Adani Solar panels, with single-brand spares, ALMM-verified supply, and channel-partner warranty handling rather than a claim routed to a foreign legal entity. For any subsidy-linked, DCR-bound, open-access or net-metering project, neither imported brand is eligible in any case, switch to ALMM-listed Adani Solar.

How Heaven Green Energy Helps for Imported Panel Projects

Heaven Green Energy delivers solar EPC across the commercial, industrial, and utility-scale segments. As an authorised Channel Partner of Adani Green Energy, the modules we install are ALMM-listed Adani Solar panels; where a project is weighing an imported SKU against a domestic one, we run the same disciplined evaluation workflow:

  • RFQ stage: landed-₹/W quotes, BoS modelling, and LCOE comparison that prices any imported SKU against the ALMM-listed Adani Solar equivalent on the same basis.
  • Procurement: supply contracts with BIS verification on the exact SKU, duty and landed-cost computation, and payment milestones in writing.
  • Logistics: delivery scheduling to site, inland transport with damage-rate accountability, and acceptance checks against the manufacturer’s packing list.
  • Installation and commissioning: Engineering design, structure fabrication, DC and AC cabling, central or string inverter integration, Supervisory Control and Data Acquisition (SCADA) commissioning.
  • 25-year O&M: Operations and Maintenance contracts with module-level monitoring, soiling-loss management, and warranty-claim handling on your behalf.

Explore the services that match your project:

Frequently Asked Questions

Are Jinko and Longi solar panels ALMM-listed in India in 2026?

No. Neither Jinko Solar nor Longi Green Energy appears on MNRE’s ALMM List-I (updated 16 September 2026), so the Tiger Neo and Hi-MO 7 / Hi-MO X6 product lines are not eligible where ALMM applies: PM Suryaghar residential subsidy projects, Central Financial Assistance (CFA) institutional rooftop schemes, government and PSU procurement, and every open-access or net-metering project. They remain usable only for private projects outside the ALMM order, such as captive behind-the-meter plants with no net metering or open access.

What is the price difference between Jinko Tiger Neo and Longi Hi-MO X6 in India?

Prices are quote-specific and move weekly, so compare current landed quotes. Both brands pay the same customs duty (20% BCD plus 20% AIDC) and 5% IGST. Hi-MO X6 usually costs more at the factory gate because of its HPBC back-contact cells, but its listed module efficiency (up to 22.5%) is not higher than Jinko’s 72-cell Tiger Neo (up to 23.42%) or Longi’s own Hi-MO 7 (up to 23.0%), so the premium has to be justified on other grounds, such as rooftop appearance or warranty terms.

Can I use Jinko or Longi panels for an open-access solar project in India?

No. Under MNRE’s ALMM order, restated in its O.M. of 30 July 2026, open-access projects must use ALMM List-I modules, and those commissioned after 31 December 2026 must also use ALMM List-II cells. Neither Jinko nor Longi is on ALMM List-I, so neither can be used for an open-access project. Their remaining Indian uses are private projects with no open access, net metering or government involvement.

What is the warranty difference between Jinko and Longi solar panels?

Jinko’s Tiger Neo 72-cell and Longi’s Hi-MO 7 datasheets both give a 12-year product warranty and a 30-year linear power warranty, with about 1% first-year degradation and 0.4% a year after that, leaving 87.4% guaranteed output at year 30. Longi lists a 15-year product warranty and a 25-year power warranty for the Hi-MO X6 Explorer. Read the warranty document itself for the exact year-by-year figures. For how annual degradation actually erodes warranty value over 25 years, see our solar panel degradation and warranty guide.

Which Indian utility-scale developers have used Jinko and Longi panels?

There is no reliable public breakdown of how many megawatts of Jinko or Longi modules each Indian developer has installed, so treat any such figures with caution. For new projects the bigger question is eligibility: open-access, net-metering and government-linked projects now need ALMM-listed modules, and neither brand is on ALMM List-I.

Is the basic customs duty on Jinko and Longi panels different?

No. Since the Union Budget 2025-26, imported solar modules under tariff heading 8541 attract 20% Basic Customs Duty plus a 20% Agriculture Infrastructure and Development Cess (40% in total), the same for both brands. In addition, an integrated Goods and Services Tax (IGST) of 5% (since 22 September 2025) on the assessable value plus duty applies on import. Check whether any anti-dumping duty notification applies to your specific product and exporter before you order.

Do Jinko and Longi panels meet BIS IS 14286 certification?

Any module sold in India must be registered with BIS against IS 14286, and both brands’ datasheets cite IEC 61215 (performance) and IEC 61730 (safety) certification; Jinko’s Tiger Neo datasheet also cites salt-mist and ammonia resistance. However, BIS certification is SKU-specific, always verify the exact model number on the BIS portal before placing a purchase order, as not every variant in a brand’s catalogue is automatically covered.

Should I import Jinko or Longi for a residential rooftop project under PM Suryaghar?

No. PM Suryaghar requires ALMM List-I modules, and neither Jinko Tiger Neo nor Longi Hi-MO 7 / Hi-MO X6 is currently ALMM-listed. Installing either brand on a PM Suryaghar project will fail the DISCOM inspection and forfeit the central subsidy of up to ₹78,000. For residential rooftop, we install ALMM-listed Adani Solar panels as an authorised Channel Partner of Adani Green Energy. See our how to choose solar modules guide for the full domestic-brand decision tree.

Written by
Akash Hirpara

Co-Founder of Heaven Green Energy. Runs finance, procurement, and channel-partner programs — including CAPEX/OPEX/RESCO models and MNRE subsidy processing.

Ready to Go Solar?

Turn this knowledge
into real savings.

Get a free site assessment and custom savings proposal, no cost, no commitment. Our engineers will visit your location within 24 hours.

Call WhatsApp